800.558.5571 
Chat 
dpl Flex Mitt Light Therapy Pain Relief
The dpl® Flex Mitt relaxes muscles and improves circulation to provide relief for arthritis pain and stiffness, nerve injury, carpal tunnel syndrome, stress injury, and aches in the hands. Medical-grade infrared lights reach deep, but are safe and natural, and built to last. Guests will feel better in just 20 minutes! FDA-cleared. OTC Class II medical device.
Features & Benefits
Flex Mitt:Medical-grade LED lights
Deep-penetrating relief for joints and soft tissue
Relieves pain and stiffness
Increases blood circulation
Accelerates healing, repairs tissue, and relaxes muscles
Enhances recovery from exercise or injury
Safe for all skin tones
Rechargeable battery to allow mobility
Medical-Grade LEDs:
880nm Infrared
660nm Red
Note: On the dpl Flex Mitt, you will only see one row of red LEDs light up when the device is turned on. The other LEDs are in the infrared light spectrum and cannot be seen with the human eye. Please know that if you see red lights while the device is turned on, the device is working (pattern of lights may vary). Device must be unplugged to power on. If pressing power button does not turn on device, try PRESS AND HOLD.
Operating Instructions
1. Fully charge device (2-4 hours).
- Your device may have a residual charge from the factory out of the box, indicated by a solid charging light when you turn it on. For best results, fully deplete this charge before plugging your device in.
- Your device will require 2-4 hours to fully charge each time. The indicator light will turn solid (no longer blinking) when charging is complete. A full charge will provide 2 to 3 full 20-minute treatments.
- DO NOT recharge battery after each 20-minute treatment. For best results, you should fully deplete the battery before recharging. Failure to do so will progressively shorten battery life.
- Battery charge will diminish over time. For best results, conduct treatments within 48 hours of charging.
2. Wash and dry treatment area prior to use.
3. Insert hand into dpl Flex Mitt.
4. PRESS AND HOLD the power button to start device. Device must be unplugged; it will not turn on while plugged in. A light on the battery pack will show when the device is turned on.
5. Leave device over the treatment area for 15-20 minutes.
6. The device is equipped with an auto shut-off function at 20 minutes.
7. Press & hold the On/Off button at any time prior to auto shut off to stop the device.
8. Device may be used multiple times per day. Do not exceed 3 treatments per day, per treatment area.
Troubleshooting
Device not turning on:
Is the device fully charged?
Is the power button turned on? A light on the battery pack will show when the device is turned on.
Is the device plugged in? The device will not turn on while plugged in, the device must be unplugged to turn on.
Device is not charging:
Is USB charging cord firmly inserted into device? (Does power indicator light turn on?)
Try different wall outlet or power source to confirm power is available.
Try a different USB cord to ensure it is working properly.
Device shuts off abruptly prior to completion of 20-minute treatment:
Device is designed to shut off automatically after 20 minutes.
Device may shut off automatically after multiple repeated uses if the device exceeds desired temperature. Allow device to cool for several minutes and try again.
Some lights appear not to be on:
The Infrared (IR) light spectrum is not visible to the human eye. These lights will look as if they are not on but are operating properly. If red lights are on, the device is operating as designed. On the dpl Flex Mitt you will only see one (1) row of red LED’s light up when the device is turned on (Pattern of lights may vary).
The dpl® Flex Mitt relaxes muscles and improves circulation to provide relief for arthritis pain and stiffness, nerve injury, carpal tunnel syndrome, stress injury, and aches in the hands. Medical-grade infrared lights reach deep, but are safe and natural, and built to last. Guests will feel better in just 20 minutes! FDA-cleared. OTC Class II medical device.
Features & Benefits
Flex Mitt:Medical-grade LED lights
Deep-penetrating relief for joints and soft tissue
Relieves pain and stiffness
Increases blood circulation
Accelerates healing, repairs tissue, and relaxes muscles
Enhances recovery from exercise or injury
Safe for all skin tones
Rechargeable battery to allow mobility
Medical-Grade LEDs:
880nm Infrared
660nm Red
Note: On the dpl Flex Mitt, you will only see one row of red LEDs light up when the device is turned on. The other LEDs are in the infrared light spectrum and cannot be seen with the human eye. Please know that if you see red lights while the device is turned on, the device is working (pattern of lights may vary). Device must be unplugged to power on. If pressing power button does not turn on device, try PRESS AND HOLD.
Operating Instructions
1. Fully charge device (2-4 hours).
- Your device may have a residual charge from the factory out of the box, indicated by a solid charging light when you turn it on. For best results, fully deplete this charge before plugging your device in.
- Your device will require 2-4 hours to fully charge each time. The indicator light will turn solid (no longer blinking) when charging is complete. A full charge will provide 2 to 3 full 20-minute treatments.
- DO NOT recharge battery after each 20-minute treatment. For best results, you should fully deplete the battery before recharging. Failure to do so will progressively shorten battery life.
- Battery charge will diminish over time. For best results, conduct treatments within 48 hours of charging.
2. Wash and dry treatment area prior to use.
3. Insert hand into dpl Flex Mitt.
4. PRESS AND HOLD the power button to start device. Device must be unplugged; it will not turn on while plugged in. A light on the battery pack will show when the device is turned on.
5. Leave device over the treatment area for 15-20 minutes.
6. The device is equipped with an auto shut-off function at 20 minutes.
7. Press & hold the On/Off button at any time prior to auto shut off to stop the device.
8. Device may be used multiple times per day. Do not exceed 3 treatments per day, per treatment area.
Troubleshooting
Device not turning on:
Is the device fully charged?
Is the power button turned on? A light on the battery pack will show when the device is turned on.
Is the device plugged in? The device will not turn on while plugged in, the device must be unplugged to turn on.
Device is not charging:
Is USB charging cord firmly inserted into device? (Does power indicator light turn on?)
Try different wall outlet or power source to confirm power is available.
Try a different USB cord to ensure it is working properly.
Device shuts off abruptly prior to completion of 20-minute treatment:
Device is designed to shut off automatically after 20 minutes.
Device may shut off automatically after multiple repeated uses if the device exceeds desired temperature. Allow device to cool for several minutes and try again.
Some lights appear not to be on:
The Infrared (IR) light spectrum is not visible to the human eye. These lights will look as if they are not on but are operating properly. If red lights are on, the device is operating as designed. On the dpl Flex Mitt you will only see one (1) row of red LED’s light up when the device is turned on (Pattern of lights may vary).
