ViBrowLash Lash & Brow Tinting

• ViBrowLash Activator
• ViBrowLash Color Cream (color of choice)
• ViBrowLash CleanUp
• Oil-Free Makeup Remover
• ViBrowLash Applicator Brush
• Glass Dappen Dish or Plastic Cup
• Gloves
• Wooden or Plastic Mixing Sticks
• Rubber Mixing Bowl
• Cotton Rounds or Esthetic Wipes
• Tissues
• Eye Wash or Eye Wash Station
• Cotton Swabs
• Timer

• 1. Put on gloves. Apply Oil-Free Makeup Remover to a cotton round or esthetic wipe. Using a downward motion, cleanse eyelashes thoroughly. Lashes should be free of oil and makeup and completely dry before beginning ViBrowLash service.
• 2. Using a 50/50 or 1:1 ratio, mix equal parts Activator and Color Cream in glass dappen dish and stir with mixing stick until the consistency is that of a creamy paste. The mixture shouldn’t be too thin or too thick.
• 3. Apply protection pads by instructing client to look up. Apply a thick layer of eye cream under the lower eyelid. Then place the protection pad under the lashes of the lower lid, which will prevent the product from staining the skin. The cream prevents the protection pad from moving. Pro Tip: Give your client a few moments to adjust to the eye pads and ensure the eye protection pads aren’t so close to the client’s eyes that they cause them to water.
• 4. Using Application brush, apply the mixture to lower lashes first on both eyes. Make sure the product covers lashes, including those at the corners of the eyes, from base to tip. When lower lashes are completed, instruct client to close his or her eyes until the application and removal process is complete. Apply mixture to upper lashes from base to tip. Again, make sure the corner lashes are covered using a tint brush, mascara wand, or disposable lipstick brush.
• 5. Set timer for 10 minutes. Note: If the product accidentally gets into the eyes, take client to an eyewash station and flush eyes with Eye Wash Solution immediately. Rubbing the eyes can cause further irritation. If no irritation occurs, you can reapply the product. If product gets on the face, remove it quickly with soap and water. Do not use Clean Up directly on lashes, eyelids, or eye area. Pro Tip: As the product develops, it may expand and migrate beyond desired area. As this occurs, you may wipe the expanded product off of the skin using a cotton swab, round, or esthetic wipe. Remove excess product around the eye area to prevent discoloration or temporary staining of the skin.
• 6. Remove eye protection pads. While your client’s eyes are closed, use a round cotton pad dampened with water in a downward motion to remove product until no residue is visible. Hold tissue near eye area to capture excess water. Offer a dampened cotton pad and dry cotton pad so the client can wipe eyes for additional comfort. Pro Tip: If you get Color Cream on hands while mixing, use a cotton ball dampened with Clean Up to remove. Wash hands with soap and water immediately.

Note: Developing time for brows differs depending on temperature fluctuation, the texture and coarseness of client’s hair, and the hair’s original color. If eyebrows aren’t dark enough, you can reapply Color Cream and allow to develop for additional minutes.

• 1. Put on gloves. The client should be comfortable and sitting upright with head slightly tilted back. Do not apply the product to the client with his or her head in a fully reclined position as this could increase risk of the product getting into eyes.
• 2. Apply Oil-Free Makeup Remover to a cotton round or esthetic wipe. Using an upward and outward motion, cleanse eyebrows thoroughly. Brows should be free of oil and makeup and completely dry before beginning service.
• 3. Using a 50/50 or 1:1 ratio, mix equal parts Activator and Color Cream in glass dappen dish and stir with mixing stick until the consistently is that of a creamy paste. The mixture shouldn’t be too thin or too thick.
• 4. Using Applicator Brush, apply mixture to client’s brows. Make sure eyebrow hair is completely covered, but do not press product into the skin. Alternatively, you may use a disposable mascara wand or lipstick brush.
• 5. Set timer for 3 minutes. Note: If the product accidentally gets into the eyes, take client to an eyewash station and flush eyes with Eye Wash Solution immediately. Rubbing the eyes can cause further irritation. If no irritation occurs, you can reapply the product. If product gets on the face, remove it quickly with soap and water. Do not use Clean Up directly on lashes, eyelids, or eye area. Pro Tip: As the product develops, it may expand and migrate beyond desired area. As this occurs, you may wipe the expanded product off of the skin using a cotton swab, round, or esthetic wipe. Remove excess product around the eye area to prevent discoloration or temporary staining of the skin.
• 6. Use a round cotton pad dampened with warm water in an upward and outward motion to remove product from the brows until no residue is visible. Check the color of the brows. If brows aren’t dark enough, reapply and allow them to process again until the desired color is achieved. Pro Tip: If you get Color Cream on hands while mixing, use a cotton ball dampened with Clean Up to remove. Wash hands with soap and water immediately.